Echelon SmartServer 2.2 Hardware User Manual

SmartServer 2.2Hardware Guide 078-0346-01F

You can also view free online training or enroll in training classes at Echelon or an Echelon training center to learn more about developing devices.

Region Languages Supported Contact Information Korea Korean Echelon Korea #505 JPLUS Tower 164-3 Samsung-Dong, Gangnam-Gu Seoul 135-881 Republic

xii Preface

1 Assembling the SmartServer Hardware This chapter describes how to mount the SmartServer hardware inside a suitable enclosure. It describes how to

Assembly Overview You need to mount the SmartServer and connect it to an IP network before you can configure it and begin using its embedded applicat

b. Open a W browser and enter the following URL: 192.168.1.222. Your SmartServer home page opens. c. Click the Login button. A login dialog appear

4 Assembling the SmartServer Hardware

Wiring the SmartServer Connections After you mount the SmartServer, you can wire its connections. The SmartServer has two rows of screw terminals, a

Connecting the Screw Terminals The SmartServer has two rows of screw terminals located on the top and bottom edges of the enclosure. The screw termi

! Safety Warning The SmartServer uses a Poly-carbonmonoflouride Lithium Coin battery. THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED BY AN I

Echelon, i.LON, LON, LONWORKS, LonTalk, Neuron, LONMARK, 3120, 3150 and the Echelon logo are trademarks of Echelon Corporation registered in the Unit

The following table lists the enclosure marking for each of the high-voltage AC power mains screw terminals and their connection type. Screw Termina

! Sicherheitshinweis: Vorsicht Netzspannung! Stellen Sie sicher, daß die Netzspannung ausgeschaltet wurde (Schalterstellung OFF), ehe der Gehäused

The following table lists the enclosure markings for the LONWORKS network screw terminals on the SmartServer and their connection type. Screw Termi

The following table lists the enclosure markings for the RS-232 and RS-485 port screw terminals and on the SmartServer and their connection types. S

Notes: If your external GSM modem requires a carrier detect line, you can attach one end of a 22-gauge (AWG) stranded wire to the carrier detect port

and RS-485 serial ports, and use a custom driver for communication between the SmartServer and the devices over the RS-232 or RS-485 serial interface

You can connect the dry contact relay outputs on the SmartServer to a voltage source and a load. When an ON value is asserted, the circuit will be c

DC Voltage SourceInductive LoadDC +DC -Inductive LoadAC LineAC NeutralSSR- Control +OutputLoad Resistor5 6 7 8AC Voltage SourceSwitched AC LineSwitch

The following table lists the enclosure markings for the pulse meter input screw terminals on the SmartServer and their connection type. Screw Ter

Digital Inputs The SmartServer has two optically isolated, polarity-sensitive digital inputs that you can use to monitor switch and sensor devices.

Table of Contents FCC Compliance Statement – Class B ... vi IC Compliance Statement – Cl

+12V < 20mA Output The SmartServer contains one +12VDC outlet that can provide up to 20mA. The +12V <20mA output is available on screw termin

Connecting the Ethernet Port After you have connected all the required screw terminals on the SmartServer for your system, you can connect the RJ-45

Connecting the Telephone Line Port ! Safety Warning The SmartServer’s telephone modem must only be used with telephone circuits equipped with proper

2 Using the SmartServer LEDs and Buttons This chapter describes how to use the LEDs and buttons on the SmartServer hardware.SmartServer 2.2 Hardwa

Using the SmartServer LEDs The SmartServer has a number of LEDs that provide status information. The following figure and table display and describe

LON BIU/RX For PL models of the SmartServer, this LED is the Band In Use (BIU) indicator. It lights whenever there is a signal present on the band t

shortcut menu. The Setup – Reboot dialog opens. Click Reboot to start the reboot. • To reboot your SmartServer using the console application, ente

www.echelon.com

iv Preface

Preface Echelon’s SmartServer is a low-cost, high-performance controller, network manager, router, remote network interface, and Web server that you

FCC Compliance Statement – Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 1

Welcome The SmartServer is a low-cost, high-performance controller, network manager, router, remote network interface, and Web server that you can us

72102R-440 (FT) x x x 72103R-440 (PL) x x 72103R-460 (PL) External coupling x x Note: You can order programmability and IP-852 activation keys fo

• SmartServer 2.2 Power Line Repeating Network Management Guide. Describes how to install a PL-20 repeating network and how to use the SmartServer