Echelon SLTA-10 User Manual download pdf (Page 1)

The LON Automation Interface Module provides a com-

munications link between a Greengate lighting panel and

a system that uses the LON Protocol. This allows a LON

based system to have the ability of turning On or Off relays

or groups of relays within a Greengate lighting panel as well

as get status from relays or switches. The LON Automation

Interface Module is custom congured for your job site’s

needs as to what relays and groups it will control or monitor.

Before You Begin

The LON AIM uses an Echelon SLTA-10,TP/FT-10 device

to communicate with the LON system.

The LON AIM ships without the motherboard installed in

the enclosure unless the desired programming has been

given to the factory prior to shipment.

As each site is pre-congured, it will be necessary to provide

technical support with the necessary programming informa-

tion to ship the motherboard to the site. Please see the end

of this document to obtain the paperwork that must be lled

out for the conguration of this unit.

The unit will be pre-congured for the connection informa-

tion for your site based on the information provided to us.

A system integrator mapping table will be provided.

Each LON AIM unit has the capability of commanding and

monitoring a total of 1200 points. Please note that your

AIM unit has been precongured for your site’s panel and

desired points to command and monitor. Please refer to

the systems integrator mapping table for the information

on how the LON network variables relate to the Greengate

lighting control points.

This document describes the installation process for

the AIM unit. Questions should be referred to Cooper

ControlsTechnical Support Department.

Figure 1: Automation Interface Module in Enclosure

Getting Started

1. Do not discard these installation instructions. Please keep

for future reference and operation information.

2. Use only as intended and at the listed voltage.

3. All installation and service must be performed by qualied

personnel or service technicians.

4. Install in accordance with the National Electrical Code and

any other codes which may apply.

5. Installation and wiring information contained in this

document is based on industry-accepted standards and

practices. If conicts exist between these instructions and

any applicable codes or ordinances, please contact Cooper

Controls before proceeding with the installation.

Mounting the AIM Unit

1. Choose a dry location convenient within 6 feet of the Greengate

lighting panel that also has access to the LON network.

2. Mount the enclosure on a rm surface using the two top

predrilled mounting holes. Drill additional holes as needed.

3. Low voltage network connections for the Greengate Network

and the BACnet connection to the AIM enclosure should be

done through conduit. Bring wiring in conduit through the left,

top or upper right side. The lower right corner of the enclosure

is reserved for the high-voltage power connection.

4. Remove all cuttings and dirt before providing power to the AIM

unit.

Cooper Controls

203 Cooper Circle, Peachtree, GA 30269

800-553-3879

www.coopercontrol.com

LON Automation Interface Module (Serial

Version)

INSTALLATION SHEET

Model# AIM-LON-SER

General Information

Cooper Controls

203 Cooper Circle, Peachtree, GA 30269

800-553-3879

www.coopercontrol.com

1 2 3 4 5

Summary of Contents

Page 1 - Version)

The LON Automation Interface Module provides a com-munications link between a Greengate lighting panel and a system that uses the LON Protocol. This a

Page 2 - OEMPrtl Pro

Wiring the AIM to the Greengate NetworkWiring Notes1. All low-voltage wiring must be run in separate conduit from line-voltage wiring.2. Disconnect

Page 3 - AIM Item Reference

1. AIM Port S2 (Greengate Lighting Connection) Transmit and Receive LEDs.2. AIM LED stack - the following LEDs are diagnostic indica-tors: Archive V

Page 4

Automation Interface Module (AIM) LonTalk WorksheetPlease ll in the below information for each panel that needs to be accessed via LON.Relay Outputs

Page 5 - 800-553-3879

All products manufactured by Cooper Controls and identiﬁed with the Greengate brand are warranted to be free from defects in material and workmanship

Comments to this Manuals

No comments

Echelon SLTA-10 User Manual Page 1

Browse online or download User Manual for Unknown Echelon SLTA-10. LON Automation Interface Module (Serial Version)

Summary of Contents

Comments to this Manuals